This page contains information about the Service Manual for the EPS Plus from Ensoniq Corporation. Hello Gslutz, im searching for schematics for the Ensoniq EPS Can someone help You wont find the service manual for free on the web. 21 EPS—16 PLUS Service Manual Table of Contents — 1 Table of Contents . For more information about the Poly-Key Keyboard assembly, see ENSONIQ.

Author: Kizil Tashakar
Country: United Arab Emirates
Language: English (Spanish)
Genre: Education
Published (Last): 2 November 2012
Pages: 483
PDF File Size: 4.52 Mb
ePub File Size: 5.61 Mb
ISBN: 723-5-22797-841-5
Downloads: 3238
Price: Free* [*Free Regsitration Required]
Uploader: Dalrajas

Cutoff Frequency 7 – 2 Ensoinq A Sequence Resample With Effects Why won’t the EPS let me edit converted Mirage sounds? Turn the unit over, top down, and remove the four 4 screws that attach the Wheel assembly to the case.

ENSONIQ EPS Musician’s Manual

Figure 1 is a magnified view with each of the components to be replaced clearly labelled. Esp Effects Test 2 Turn the unit ON. How do I Mix a Track or a Song?

Re-saving a SYSEX file now uses the correct file name; previously, the file was saved using the name of the last-saved file. For this reason, majual necessary, you will be swapping it out as a whole unit. Sorry – these are not available on DVD.

Turn the system on. Create a short sequence by pressing Record and Play at the same time Use the sustain right pedal to verify that sustain works, then stop the sequencer using the sequencer left pedal Press Cancel-No If one or both of the footswitches do not operate properly, make sure that the footswitches are set to the proper sservice as outlined on page 50 of servicce EPS Musician’s Manual The above test assumes that the left pedal is set for sequencer control and the right pedal is set for sustain this is the default.


Before replacing the Power Supply board, first make sure that the cardboard insulator is in place. Power up, test the unit, aid re-attach the lid see below. The EPS PLUS writes information to every track on a disk, so it is imperative that the disk be of superior quality and certified for double-sided use. Punching In” On A Track To reiterate, we do not, under ensooniq circumstances, recommend the Insertion of an actual disk during transport nor do we recommend the use of cardboard ensonis sheets in place of plastic ones.

Carefully turn the unit right side up. Disconnect the cables from the Disk Drive, sdrvice particular attention to the polarity. Mono Output And Headphone Test You must have O.


When installing the keyboard mahual into the EPS, be sure that the keyboard cable is flat under the keyboard and that the ferrite bead is not trapped on top of the main board. In this case, you should test the Power Supply unloaded before proceeding. Install the new Line Filter from outside the case using the two screws, star washers and nuts.

Verify that no pressure effect occurs. This item is a.


Carefully remove the Control Panel from the unit just enough to unplug the pin ribbon cable from the KPC board. Instead, the display will read: Sfrvice you can’t isolate a problem that seems related to the display, the display can be forced into Self-test mode using the following procedure. Install die two 2 self tapping screws on either side of the unit 3. Press all the control panel buttons in any order.


Detune Rate and Amt parameters were interconnected, changing either one changed the other. Large original over-sized drawings will need to be taped together. Insert the new Transformer and attach it to the base using the four screws and flat washers. Be sure that xervice cable lies flat beneath the Keyboard and is not pinched under the Keyboard frame. Disconnect the Keyboard cable from manuwl main board.

Avoid over-tightening screws in the plastic case when executing any repair procedure! The most likely system error was 1 This has been fixed in the current version.

Be sure to keep the soldering iron on an angle away from the plastic case to avoid burning the plastic case. The test cycle will continue. Attach the mounting brackets to the control panel trying to use the same holes.

Ensoniq Corporation – EPS Plus – Service Manual

Plug the pin ribbon cable from the Communication Test Board into J Plug headphones directly into headphone jack. Power Supply Ensiniq To reduce the occurrence of fuse failure when a memory expander is installed, fuses F3 and F4 were changed from 3. Instruments And Banks Setting The Input Level